What to look at before we arrive
Note whether the drip is hot, cold, or both, whether the stop under the sink still turns, and whether water is at the base of a toilet or only in the bowl.
Drips and spray at the faucet
A worn cartridge or a failed seat usually shows as a steady drip or a spray at the handle. Builder-grade trim in later houses often fails at the cartridge while the valve body is still good. We repair that when the body is sound, and we replace the faucet when the body is pitted or cracked.
A shower or tub valve that will not shut
If the tub keeps running after you close the handle, stop using it and close the house valve if the stop in the wall will not turn. Forcing a stuck stop is how a small drip becomes an open line in the wall.
Toilets that rock or stain at the base
A rocking bowl can break the wax seal and wet the floor. We check the flange and the closet bolts before we talk about a new toilet or a simple reset. Sink installation follows the same order: test the stops, set the faucet, and watch the trap.
Faucet, toilet, and sink work our plumbers take
New faucets, toilets, and sinks go in when that is the job, and we still fix a drip, a running tank, or a worn cartridge when the valve body is still sound. The visit starts at the stops, not at the trim.
Faucet and sink work
Faucet installation and sink installation include new supply lines, a checked trap, and a leak test with the water back on. Soft city water here is easy on scale, so most faucet failures are worn cartridges, tired seats, or stops that have seized, not mineral crust inside the body.
Toilet setting and trim
Toilet installation starts with a flange that is level and sound. We set the bowl, replace supply lines that have gone stiff, and test the fill and flush before we leave the floor dry. If the flange is broken, we repair that first rather than hide it under a new wax ring.
If a valve will not shut or a supply line has already split, call the fixture line at (903) 568-7570.
Why trim fails in this housing
Later production houses toward Loop 323 and in places like Hollytree often have builder-grade cartridges that give out first. In earlier houses around Brick Streets, Charnwood, and the Azalea District, original stops seize and supply lines go brittle. Chloramine in the city supply can age those rubber connectors. We bring the stops and the lines, not only the pretty trim.
Faucet and toilet installation cost in Tyler
Fixture prices in Tyler vary with the faucet or toilet you choose and with the condition of the shutoff, flange, or supply line behind it.
| Service | Typical cost in Tyler |
|---|
| Faucet repair | $125 to $300 |
| Faucet replacement | $150 to $400 |
| Toilet repair | $125 to $350 |
| Toilet installation | $250 to $700 |
| Shower valve or cartridge work | $200 to $600 |
These figures are typical ranges for Tyler and the East Texas area, not a final bill. The final price depends on the problem, the parts, how hard the work is to reach, and whether the call is after hours. We diagnose on site and give you the number before any repair starts.
Compare these figures with the full list on our plumbing cost in Tyler page, or call (903) 568-7570.
Questions about fixture work in Tyler
Can you repair a dripping faucet in Tyler, or do I need a new one?
If the valve body is sound, we replace the cartridge or the seats and test the shutoff. A cracked or badly pitted body is a faucet replacement. We will show you which one you have before we pull the trim for good.
Do you install toilets and sinks, or only repair the ones already there?
We do both toilet installation and sink installation, and we repair running tanks and dripping faucets when the parts will hold. A new fixture still needs a sound flange or a working stop, and we fix that first.
What if the stop under the sink will not turn?
Leave it. A seized stop that snaps becomes an open line in a cabinet. We will isolate the water from another valve and replace the stop as part of the fixture visit.
How long does faucet or toilet installation take?
Most single-fixture jobs, like a faucet or toilet swap, take 1 to 2 hours once the tech is on site. Jobs take longer if the shutoff valve is seized, the flange is broken, or supply lines need to be replaced along with the fixture.
Can I install a new faucet or toilet myself?
You can, if the stops turn freely and the flange is sound. Problems start when a seized stop snaps or a flange is cracked under an old toilet. If you are not sure what is behind the trim, have a plumber check it before you buy the fixture.
Do you install bidet attachments or touchless faucets?
Yes. Touchless faucets and bidet attachments need the same supply line and stop check as a standard fixture, plus a power source for electronic models. We confirm the rough-in matches the fixture before we order parts.
What brands of faucets and toilets do you install?
We install most major fixture brands sold at Tyler area supply houses and home centers. Bring the model box or a photo of the fixture and we will confirm fit before the visit.
When the drip will not quit
If you need a plumber in Tyler for fixture installation, a faucet repair, or a toilet that will not set dry, call us at (903) 568-7570. You can also read about the shop, scan the FAQ, or use the contact page to send the street and which fixture is dripping.
Service ZIPs: 75702, 75701, 75703, 75704, 75705, 75706, 75707, 75708, 75709, 75758